Powder metallurgy is a growing sector in industrial production, as it offers outstanding energy, cost and material savings in comparison with established processing routes such as casting. Hot work toll steels are usually produced by ingot metallurgy, but also by powder metallurgy, namely hot isostatic pressing and powder forging routes. In this paper we investigate the possibility of production of a hot work tool steel (AISI H13) by conventional (die compaction and pressureless sintering) and metal injection molding routes, aiming to reduce cost and production time. The sintering behavior was studied from 1250 °C until 1430 °C and the resulting parts were compared in terms of microstructure, hardness and tensile strength. The results showed that both shaping routes together with pressureless sintering are suitable to produce this alloy. By combining the best shaping approach and a tailored sintering cycle, it was possible to produce samples with 400 HV10 as well as tensile strength of 1 GPa, which are comparable to the ones obtained by powder forging.

When multifunctional surface engineering processes that combine purpose-oriented phases are applied to soft substrates, a combination of high wear resistance, high load support and low coefficients of friction can be achieved. In this study, the effects of different nitrided layers on the tribological behaviour of a diamond-like carbon (DLC) film deposited on a SAE 1040 steel were investigated. The nitriding was carried out under different temperatures and gas mixtures to create three distinct nitrided layers: two compound layers with predominant ε and γ' phases and a diffusion layer. All of the surfaces were then coated with DLC deposited via plasma-enhanced chemical vapour deposition (PECVD). The tribological tests indicated that the best performance was achieved for a specific combination of hardness, surface roughness and nitride type. The best load-bearing capacity between the DLC coating and the soft substrate was achieved when the nitrided layer was primarily a diffusion layer.

Abstract To modify the surface structure of AISI 1005 steel and its properties without any dimensional loss, different plasma surface treatments were performed at low temperatures (500 ºC) in this study. The samples were subjected to single plasma treatments including: nitriding (N5% and N3%), carburizing (CE) and ferritic nitrocarburizing (NC) and to duplex treatments of nitriding followed by carburizing (N5%+CE and N3%+CE) and ferritic nitrocarburizing followed by carburizing (NC+CE). The gas mixture used for these treatments was varied as follows: nitriding (5%N2+95%H2 and 3%N2+97%H2), carburizing (5%CH4+95%H2) and ferritic nitrocarburizing (5%N2+1.5%CH4+93.5%H2). A microstructural characterization of the samples was carried out using optical and scanning electron microscopy in addition to XRD analysis. Microhardness testing was also performed. The XRD analysis showed a stabilization of the outermost cementite layer for all of the carburizing treatments. The results show that a greater hardness increase was achieved for the nitriding treatment as well as a more regular compound layer. However, a greater depth of hardening was obtained in samples with NC+CE and N5%+CE, which extended to the hardened depth to 800 µm.

Processing of high manganese austenitic sintered steels present several challenges concerning thermodynamic reactions that occur during the sintering of these materials such as Mn oxidation, sublimation and even the formation of liquid phases or undesired compounds, e.g. grain boundary carbides. Therefore it is extremely important to adjust the sintering parameters to obtain the adequate microstructure and properties. In this work, the effect of some sintering parameters, i.e. temperature, gas atmosphere and cooling rate are studied by dilatometry. The experiments revealed that the sintering temperature has small impact on the microstructure formation. On the other hand, the decrease on oxygen chemical potential in the furnace atmosphere resulted in less oxidation of the powder particles. Moreover, the increasing on the cooling rate to 50 °C/min avoided the formation of grain boundary carbides. As a main conclusion, a special sintering cycle for Hadfield steel samples was suggested.

Copper is a well know material for use as heat sink or heat exchanger. However, copper has a considerable low tensile strength and temperature limit. A material that has a good thermal conductivity, low cost, but also resistance is the desired. Effects of copper on the sintering and thermal properties of iron-copper composites produced by powder metallurgy and Fe on copper-iron composites have been investigated. Copper and iron were varied from 20 to 80 vol.% in the samples, alternating the continuous phase. Sintering studies were performed by in-situ dilatometry aiming to define the proper conditions for sintering, without swelling normally associated with copper. Results indicate that the type of sintering, final microstructure, specially the phases relation and distribution and not only the amount of copper, have a great effect into the thermal properties. By controlling the sintering parameters, it is possible to obtain dimensionally stable samples with higher thermal conductivity and lower copper amount.

In this work, plasma carburizing of sintered pure iron at low temperature was investigated. Samples were carburized under a dc abnormal glow discharge in two mixed atmospheres (5%CH4 + 95%H2 and 20%CH4 + 80%H2) at 500 °C and 700 °C for 3 and 6 hours. The influence of these parameters was investigated by Scan Electron Microscopy (SEM), X-ray Diffraction (DRX), Raman spectroscopy and microhardness measurements. There is a correlation between temperature and layer morphology, and a layer of polycrystalline cementite was obtained at 500 °C and 700 °C on a ferrite substrate. Furthermore, the carburized layer thickness increased with an increase in the treatment time and the methane percentage. The topography is very dependent on the treatment temperature.

A moldagem de pós por injeção é um processo de fabricação de elevada produtividade que possibilita obter componentes de geometria complexa, estreita precisão dimensional e boas propriedades mecânicas. Neste processo, uma mistura de uma determinada quantidade de pós e ligantes orgânicos (polímeros, ceras e óleos) é obtida por meio de uma massa de injeção (feedstock) o qual tem características reológicas adequadas para promover a injeção desta massa em uma cavidade de um molde. A produção de ligas de níquel por meio deste processo é uma alternativa para produção de produtos que requerem aplicações avançadas onde se exige resistência a corrosão e oxidação, resistência mecânica a altas temperaturas e baixo coeficiente de atrito. Neste trabalho apresentamos um estudo das propriedades microestruturais e mecânicas de uma liga de níquel (Ni-Fe-Cr-P) processada via moldagem de pós por injeção, utilizando pós de níquel carbonila com e sem a presença de fase líquida durante a sinterização. Os resultados foram comparados com a mesma liga processada por compactação de pós. Os resultados demonstraram a necessidade de maior quantidade de matéria orgânica para o desenvolvimento da massa de injeção (feedstock: 15% m/m de polímero) para os tipos de pós metálicos utilizados (níquel carbonila do tipo INCO 123) se comparado ao feedstock de ligas comerciais que normalmente utilizam uma quantidade menor de matéria orgânica (feedstock: 9% m/m de polímero). A maior quantidade de matéria orgânica necessária para a preparação do feedstock deve-se a morfologia dos pós empregados (superficie rugosa - tipo spiky) que promove retenção de carbono durante o processo de extração, ocasionando a necessidade de otimização do ciclo de extração térmica e sinterização. Ciclos mais lentos e a baixa temperatura promoveram a total retirada dos ligantes. A liga de Ni-Fe-Cr-P injetada apresentou contração de aproximadamente 50%, além de elevado teor de poros quando comparado ao material compactado, o que influenciou as propriedades mecânicas e dureza aparente do material.

The powder injection molding is a manufacturing process that allows high productivity to obtain complex geometry components, dimensional accuracy and good mechanical properties. In this process, a mixture of a quantity of powders and organic binders (polymers, waxes, oils) is obtained through injection of a mass (feedstock) which has rheological properties suitable for promoting the injection of this mass in a cavity of a mold. The production of nickel alloy by this process is an alternative to production of products that require advanced applications, which require resistance to corrosion and oxidation, mechanical strength at high temperatures and low coefficient of friction. This paper we present the study of the microstructural and mechanical properties of a nickel alloy (Ni-Fe-Cr-P) processed by powder injection molding, using carbonyl nickel powders with and without the presence of liquid phase during sintering. The results are compared with the alloy processed by powder compaction. The results demonstrate the need for increased amount of organic matter for developing the injection mass (feedstock: 15 wt.% polymer) for the types of metallic powders used (nickel INCO type 123 carbonyl) compared to commercial alloy feedstock typically use a smaller amount of organic matter (feedstock: 9 wt.% polymer). The largest quantity of organic matter needed for the preparation of the feedstock due to the morphology of the powders used (spiky) which promoted carbon retention during the extraction process, resulting in the need to optimize the extraction cycle and thermal sintering. Slower cycles and low temperature promoted the complete extraction of the ligands. The Ni-Fe-Cr-P alloy injected showed shrinkage of approximately 50%, and high levels of pores as compared to the compacted material, which influenced the mechanical properties and apparent hardness of the material.

The purpose of this work was to develop nickel self-lubricating composites using solid lubricant as second phase and obtained by powder metallurgy. The work involved the study of chemical stability and chemical interaction between the nickel alloy matrix and solid lubricating additives (molybdenum disulfide, graphite and hexagonal boron nitride). The results showed a thermodynamic stability during sintering for the composites containing the phases of graphite and hexagonal boron nitride. The presence of molybdenum disulfide phase permits a reaction with the matrix, the formation of a liquid phase of nickel sulfide and the solubilization of molybdenum in the matrix.

The present work is focused on ferrous powder metallurgy and presents some results of a development of a suitable masteralloy for use as an additive to iron powder for the production of sintered steels. The masteralloy was produced by melting a powder mixture containing approximately Fe + 20% Ni + 20% Mn + 20% Si + 1% C (wt%), in order to obtain a cast billet that was converted into fine powder by crushing and milling. It was observed presence of SiC in the masteralloy after melting that is undesirable in the alloy. Si element should be introduced by using ferrosilicon. Sintered alloys with distinct contents of alloying elements were prepared by mixing the masteralloy powder to plain iron powder. Samples were produced by die compaction of the powder mixtures and sintering at 1200 °C in a differential dilatometer in order to record their linear dimensional behaviour during heating up and isothermal sintering, aiming at studying the sinterability of the compacts. Microstructure development during sintering was studied by SEM, XRD and microprobe analyses.

In this work, stearic acid (SA) was degraded in an Ar-O2and Ar-H2post-discharge environment created by a plasma reactor with a microwave source and in an Ar, Ar-H2and Ar-O2DC (Direct Current) discharge environment created in a cathode-anode confined system. The afterglow region is useful for understanding the role of the chemically active species (O, O2, H and H2). In contrast, the discharge region allows the observation of the effects of chemically active species, charged species (ions and electrons) and photons. The influence of these species on the grafting and etching of SA was evaluated by measuring the mass variation, mass variation rate and chemical composition. The results showed that when only chemically active oxygen species are present, the SA is preferentially grafted. However, when both photons and charged species are present, the SA is more efficiently etched. When the Ar-H2and Ar environments are utilized; the SA is not efficiently degraded.

Stearic acid (CH3(CH2)16COOH) was treated with Ar and Ar-O2 (10%) pulsed DC discharges created by a cathode-anode confined system to elucidate the role of oxygen in plasma cleaning. The treatment time (5 to 120 minutes) and plasma gas mixture (Ar and Ar-O2) were varied, and the results showed that the mass variation of stearic acid after Ar-O2 plasma exposure was greater than that of pure Ar plasma treatment. Thus, compared to Ar*, active oxygen species (O and O2, in all states) enhance the etching process, regardless of their concentration. During the treatments, a liquid phase developed at the melting temperature of stearic acid, and differential thermal analyses showed that the formation of a liquid phase was associated with the breakage of bonds due to treatment with an Ar or Ar-O2 plasma. After treatment with Ar and Ar-O2 plasmas, the sample surface was significantly modified, especially when Ar-O2 was utilized. The role of oxygen in the treatment process is to break carbonaceous chains by forming oxidized products and/or to act as a barrier again ramification, which accelerates the etching of stearic acid.

In this work, 17-4PH stainless steel parts processed in a Plasma Assisted Debinding and Sintering (PADS) furnace were characterised in terms of microstructure, final density, microhardness, carbon content and tensile behaviour. To determine whether these properties were satisfactory, the same characterisation procedure was conducted on the parts processed by conventional batch furnaces that are normally employed in Metal Injection Moulding industrial plants. The properties were in good agreement, and only slight differences like an extremely low carbon content (0.003% w/o) were observed. It has been seen that not only economical advances but also intricate materials with suitable responses may be obtained using PADS.

Powder metallurgy is widely used in the manufacture of components that have complex geometry. The good dimensional control, reduction in manufacturing steps and operating costs which has favored the use of this technique for manufacturing of titanium alloys components. However, the high affinity of this material with oxygen hinders strongly the sintering process. For this, the sintering associated with plasma technology can be considered an alternative technique for the processing of this material. The strict control of sintering atmosphere performed at low pressures and the reactive species present in the plasma environment can help to improve the sintering of this material. The results presented in this paper show a good correlation between the parameters used for the compaction of the samples and the microstructure develop during the plasma sintering of samples. The microstructure of the plasma assisted samples is also affected by the particular configuration used in the plasma reactor.

Samples of unalloyed iron were sintered in the presence of an abnormal glow discharge using a confined anode-cathode configuration. The samples were placed on a holder acting as the discharge anode inside an AISI 1020 steel hollow cathode. Heating of the outer cathode was obtained by the bombardment of ions and energetic neutral particles. As a consequence of the confined geometry, the sample was efficiently heated mainly by radiation from the cathode. In order to evaluate the results of the sintering process by plasma, samples of unalloyed iron were also sintered in a resistive furnace using the same thermal cycle. The porosity, dimension and morphology of the pores were characterized by means of four basic parameters: area fraction, mean diameter, shape factor and elongation factor. The results show that the shape factor depends on the pore size, a characteristic that was not observed for elongation factor. For samples sintered in plasma reactor or conventional furnace, no significant difference in the porosity or in the pores morphology was observed.